"If the hole isn’t clean, it can be really risky!"


HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Stainless Steel Climbing Highlining Anchor
Stainless Steel Glue In Bolt

If you have the right bolt and the right glue and the right stoke, you can still screw (or glue, get it?), this up and kill someone. You don’t have to be a nuclear physicist to install a glue in bolt, but you DO have to do the simple instructions or you can kill someone. Let’s emphasize the killing someone real quick. This isn’t about long term vs short term anchors here. We are talking about them coming out, AKA killing someone if they don’t get put in correctly.

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Twisted Leg Bolt Climbing Highlining
Stainless Twisted Leg Bolt

Another way to fail, that has less consequence, is by failing to actually install the bolts you set out to do. You spent weeks reading the Bolting Bible, spent a bunch of money, used a good weather weekend, and you get there and find out the plunger is too big on your dispenser to push out the glue. Or that cheap caulk guns are too weak to push cold glue out. You could run out of battery before you finish drilling, or find out you left the extension tips to your mixing tips at home... so now you can’t put the glue in the back of the hole, after you cut open your tube! Nope, none of these have ever happened to me… nope… not me! Taking preparation and installation seriously can make you a bad-ass, otherwise you might just be a dumb-ass!

Chapter 1 - TOOL LIST

  • Bolts, duh! The softer the rock, the longer you want your bolt.

  • Glue cartridge + Dispenser ...OR Capsules

  • Spare mixing tips and extension tips

  • NOTE: 10oz fills around 10 holes roughly but if you have to change out mixing tips often, you lose quite a bit each time you change one.

  • Knife

  • Drill, and correct size bit, plus spare bits

  • Safety goggles

  • Face mask - rock dust isn’t good for you.

  • Ear plugs if drilling a lot

  • Pipe cleaner and blow pump (for really clean holes!)

  • Rubber gloves and paper towels! It can get messy.

  • Tape for a perimeter around notch so it doesn’t ooze everywhere AND you can tape mid way up your drill bit so you know how far to drill

  • Cotton swabs for detailing in case it oozes out a lot

  • Bag for garbage

  • Bag for testing mixture (see “Filling Hole” below)

  • Plastic or covered Hammer (For bolts with a tight fit)

  • Wave installation tool (for wave only)

  • Heart full of stoke and a car full of friends!

  • Bag to go on your harness for installs in the vertical world

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins What You Need Climbing Highlining Anchors
Glue In Bolting Kit


Please please don’t let your first glue in bolt be anywhere important. Do several in your backyard or your parents backyard or the backyard of someone you don’t like when they are out of town (kidding! Just kidding! Jeez). If you think that would be an eyesore, now you know how all the rock huggers feel that complain about over-bolting. You can read this Glue In Section 100x, but you will always have kinks to work out, and kinky stuff should be done at home.

Practice also helps you verify you have the right drill type, bit type, bit size, glue accessories,

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Bolt with Quick Links Climbing Highline
Glue In Bolt with Quick Links

amount of glue, cleaning tools AND TECHNIQUE. Or... you can just wing it and go learn in a popular area, but just make sure you put your name on it so we know who to troll!

Can you answer the following questions about what is in your bolt kit bag?

1. What are the min and max cure temperatures?

a. What temperature will it be when I install these?

b. Can the glue even be installed at the installation temperature?

2. What is the nozzle time? (how long can it sit in nozzle before you have to put a new one on)

a. Do I have spare nozzles

b. Do I have spare extension tips to get the glue in the back of the hole?

3. What is the working time so I don’t ruin the bond before it is cured?

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Bolt in Drilled Hole Climbing Highlining Anchor
Stainless Bolt in Drilled Hole

4. Will this glue run out of a hole if I put it in horizontal or in an overhanging rock?

5. What is the cure time for low, medium and high temps?

a. When do I plan on climbing or highlining on these bolts?

6. Did I charge my batteries for my drill? Do I have spare batteries?

7. How deep do I need to drill, and will I need a notch?

8. Do I have a way to keep things clean and tidy?

9. How many holes can I fill up with one tube?

10. Do I have the right bolt for my glue capsule (angled end for screw install and blunt end for hammer install!)

11. How am I going to put warnings on my bolt if it requires several hours to cure so no one uses them after I leave?

12. Does the fluid move in my glue capsules?

13. How long has my glue cartridge sat on my shelf?

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Drilled Notched Hole Climbing Highlining Anchor
Glue In Hole with Notch

14. Do I have the proper pipe cleaner and blower to get a really clean hole?

Chapter 3 - DRILL HOLE

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Side View of Drilled Hole with Notch Climbing Highlining Anchor

All glue in bolts have an intended hole size. Solid leg bolts are going to slip right in and P shape bolts have to be pounded in. Wave bolts act like a piton and take a lot of pounding and the Titan bolt takes a mild tap as the neck gets tight at the top. If these holes were drilled too big, it wouldn’t be the end of the world, you just lose a nice feature that they have of not falling out and you would be wasting glue.

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Drill a Notch 45 Degree angle Climbing Highlining
Drilling a Notch

Some glue ins require a notch so the bolt is inset a bit. To make a notch for a bolt you have 3 options. Drill a ½” deep hole about an inch or so away from hole and then tilt the drill bit 45 degrees towards the main hole. OR stick the drill bit inside the main hole and tilt it a lot and drill away from the hole.

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Hole Drilling Example in Wood Block
Wood Block Glue In Hole Example

OR drill 3 straight down holes, ½” deep, next to your main hole CAUTION: If the notch is too deep, you lose a lot of space in your eye, limiting what can be clipped to it. And if it is excessively deep, it could force the rope to sit on the rock creating abrasion. PLEASE: Make sure the direction the bolt is facing is the direction of the force. It is pretty easy to guess in climbing situations… straight down!

But if you are building a highline 3 point anchor 2 feet from a cliff edge, what angle will those outside bolts be???


HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Backwards P Special Circumstances Only Climbing Highlining Anchors
Backward P Example

If there is any chance this bolt will need to be pulled in more than one direction, ie: multiple highline variations or spacenets, then use a “P” shape bolt and drill the notch so the bolt will be installed BACKWARDS so the anchor rope will be pulling on the spine. This allows it to be pulled in 170 degree without the risk of twisting the bolt and compromising the glue. Bolts in general start to deform before breaking, even more so when pulling on backwards. 8mm twist bolts we tested changed shape around 10kn even though the final breaking strength was 40 or 50kn. However, if pulling sideways on them installed “normal”, it started to deform around 4kn but also had very high final breaking strengths. These tests showed us the bolts bent before twisting the bolt out of the glue. We have also found in BoltBusters that the weld on Bolt-Products straight leg series gives us wildly different results and for backward Ps, it leverages that part of the bolt that was weakened by the weld. In our backward tests, they started to bend around 20kn and broke anywhere between 21kn and 45kn after that. Installing backwards Ps are for very specific goals and they should be installed forward like recommended in almost all scenarios. This is just one solution to a unique scenario.

Contrary to what you would think, don’t drill an angled hole away from the projected force. That lever action doesn’t make the bolt stronger but puts all the force on the rock at the top. See the Book of Holes about the research done on this.

If you are using capsules, then depth AND diameter are very important to get right since you can’t just add glue if you don’t have enough and no one wants to clip a glue in bolt when they can’t see the damn glue! This is a great reason to test it at home, and if you don’t want a bolt in your backyard, pull it out before it cures. But this way, you know you got the right system at the cost of only 1 or 2 capsules. (A trick to get your depth perfect is to put several layers of duct tape mid way up on the drill bit where you want it to stop.)

Chapter 4 - CLEAN HOLE

This is a huge fear when an experienced bolter hears a new bolter is stoked to go install glue ins. If the holes aren’t cleaned really really well, someone could very likely die. Really clean it! That requires a pipe cleaner AND a blow tool. A blow tube and your lungs aren’t enough, even if you are really good at blowing. So get a dust blower like this pump, or Hilti's pump . A can of air also can do 20 to 30 holes and is light. A Battery Powered blower compatible with your drill battery can also be a game changer. A wire brush tube/pipe cleaner can be bought from anywhere. Regardless of how rough or porous the rock is, drilling a hole polishes the sides of the hole, so in order to get the glue to bond with the rock (which in case you don’t know, that is important, and if you don’t know that, please don’t put any of these in), the rock can’t have any dust film on the sides. Do a fun experiment at home, put super fine construction dust on your granite countertops at home, then try blowing them clean… blow hard… even with an air compressor you can’t get it truly clean. Same with the wire brush, you can’t JUST use the brush. Blow then brush, again and again and again until it is super clean. Always start with the blow.

Chapter 5 - TEST and CHECK

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Fresh Bolt Climbing Highlining Anchors
Glue In Installation

Dry fit the bolts, if possible, to make sure it will work. If you are putting a wave bolt into a ½” hole then you can’t do this but you can verify with a stick or the tube cleaner that the depth is perfect (too deep is better than too shallow). The biggest crux is to make sure your notch isn’t too deep or restricting the bolt from being the angle you want. Get all your stuff laid out and ready, cus when you start gluing, the working time clock is ticking. Know your working time, because if you are using Powers AC100+, and it is hot out, AND it takes you more than 1 minute to get to the next bolt, or even spend more than 30 seconds hammering in a wave bolt… you will need a lot of mixing nozzles and therefore won’t be able to fill as many holes as you think with each tube of glue. For climbing, drill and clean on your way up a route, then glue and install on your way down the rope as this will have shorter transition times.

Chapter 6 - INSERT GLUE

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Bolt Failure Bad Glue Mixing Climbing Highlining
Glue In Bolt Failure

CARTRIDGE: If you’re 100% ready to start, cut your glue cartridge open, squeeze just a bit without the nozzle to see that both colors are coming out, then install the mixing nozzle. But… before you start shoving your tip inside of holes, make sure what’s “coming” out is safe! You can’t just put the first squeeze into the hole. This is one the main reasons you will want paper towels. Squeeze a COUPLE times to make sure it is mixed properly, which you can generally tell by the color.

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Bolt Failure Glue Not Mixed Properly Climbing Highlining Anchor
Glue In Bolt Failure Bad Mixing

THEN grab a ziplock bag and squeeze a quarter size amount into the corner. Only after all that… start putting it in the hole. This ziplock bag is so you can check later to make sure your first squeeze of glue hardened. Jim Titt from said in a Mountain Project thread “over a period of 7 years the DAV recorded 17 failed resin bolts… one climber died.”

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Guide How To Fill the Hole Climbing Highlining Anchor
How to Fill the Hole with Glue

VERY IMPORTANT… Start in the back of the hole and work your way out. Don’t fill it up to the very top because the bolt will push out the amount of space it replaces. Somewhere around ¾ full is good. When you are done, squeeze some into the other corner of the bag and take it home as a souvenir… also to check your first and last squeeze to make sure both get rock hard. If they don’t, it didn’t mix right! Battery powered dispensers can help mix the glue more evenly and just be easier than a manual dispenser but they definitely cost more.

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins How To Graphic Climbing Highlining Anchor
Glue In Bolt Installation Example

How much glue do you need? You can get almost 20 bolts out of a 10oz AC glue cartridge if they are ⅜” (10mm) and short. I was barely able to do 8 when I used Hilti 500 v3 glue on long Crux Monsters.

HAMMER CAPSULES: Spin the capsule around a couple times to make sure all the resin is in liquid form because if it isn’t it won’t mix correctly. You are literally shoving harder around it so it has to be liquid. Insert with the hardener facing up. If you think of it like a cigarette, then what looks like the filter, is closest to the top of the hole. That is the hardener and if it isn’t at the top you aren’t going to be mixing anything. The capsules are glass and you are smashing a bolt through it, so wear safety goggles. Your bolt has to have a flat/blunt end. A tapered end won’t push the hardener down into the resin. Make sure you have the right size capsule because if it is a ½” capsule in a ⅝” hole, then it will be leaning to one side not mixing things evenly, and you probably won’t have enough glue to fill up your hole!

SPIN INSTALL CAPSULES: Spin the capsule around a couple times to make sure all the resin is in liquid form because it if isn’t, it won’t mix correctly. These spin installs have a glass container inside of another glass container. One has resin (the amber liquid) and the other has hardener. There are sand chunks in these so it scores sides of the hole and helps mix the glue. These capsules (at least from Petzl) require that they stick out of the hole by 10mm so you can break the glass with the hammer, then insert the bolt. These bolts must be angled on the bottom in order to mix these correctly which is different from the hammer capsules. Now to do this properly, the spinning requires mechanical spinning, and there are special adapters for your drill that you can attach the bolt and spin it. Petzl system is to manually spin the bolts in their instructional videos, but I don’t believe that is how they should be used. They say to spin the bolt 10x. That doesn’t mean 10 turns with your hand, that means 10 full rotations which is more like 20 times with your hand. If you use this system, spin them like your life depends on them. This system obviously doesn’t work for wave bolts because they can’t be spun as they fit tightly in the hole.

Chapter 7 - INSERT BOLTS

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Don't Make Messy Bolts Climbing Highlining Anchors
Messy Glue In Installation

If using a threaded rod, squirt a bead of glue along the threads before putting it in. For the bolts that don’t require hammers to install, like Bolt-Product solid legs, Petzl and Fixe bell shape or PLX, you will want to slowly push them in and TWIST them while you do it. Fixe bolts have a weld, and you want that weld facing away from force, even if it is buried under the glue. You don’t want air pockets around notches or threads. If you hear air bubbles gurgling as you push in bolt then you don’t have glue in the back of your hole!!! No bolt queefing! Pull out the bolt and make sure it is super full of glue.

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Always Bring a Hammer Climbing Highlining
Bolt Hammer with Carabiner

If you are using Wave bolts, Titans or Twist bolts, then you need a hammer, but you don’t want to hit a stainless steel or titanium bolt with a non stainless or non titanium hammer. Since that would be one expensive, fancy hammer, you can use the wave installation tool that is made from stainless and it puts the force on the right parts of the bolt, or use a rubber mallet, or plastic hammer, or just put a rag between the two metals. The point is, your hammer will transfer iron onto your fancy expensive bolts and those iron particles will start rusting making your fancy bolt look like it is corroding. This is the same reason you don’t want to grind threaded rod to the length you want if the cut end is exposed to the elements. Yes, we clip non-stainless carabiners, shackles and unfortunately most quicklinks, but they are not striking the bolt enough to transfer non-stainless to bolt.

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Stainless Steel Bolt Hammer Tool Climbing Highlining
Stainless Steel Hammer Tool

Keep in mind, the Wave bolt will twist as you hammer it, requiring you to hit it sideways to orientate it correctly, not sure if that is good for the bolt or the glue but people do it.

One option is to drill the hole bigger for the Wave Bolt, you will lose the tight fit, but you don’t need that unless you’re installing it in an overhang.


HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Warning Sign Don't Climb New Bolt
Do Not Climb Fresh Glue

If you put a perimeter of tape around a notched hole, then after gluing you can just pull the tape up and it will be a nice rectangle of glue, otherwise you risk it getting everywhere, and if the glue is red, that can look really bad. Cotton swabs are convenient for cosmetically making the glue look nice. Be sure to clean off the glue that got all over the eye of the bolt if it squished up too high. Have a lot of cotton swabs handy and a bag to put them in. Saving some of your rock dust may help because you can possibly hide the glue color by sprinkling the dust on top. No, a little dust ON TOP of your glue won’t kill anyone and will make it look nicer. Use dust and not rock crystals on your glue so there is less risk of abrasion on the rope anchor. All this cleaning is a lot easier with rubber gloves. If it is an epoxy that takes many hours or days to dry, label it with a date preferably so people don’t use it before it has safely cured.

Chapter 9 - Troubleshooting

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Messy Hilti Gun Broken Cartridge Climbing Highlining
Messy Hilti Glue Gun

1. Why doesn’t my glue come out the right color???

  • Well, that’s probably because both parts aren’t coming out! Single cartridges may not be evenly dispensing like the image below, or one of your dual cartridges have ruptured like the image with the messy Hilti gun. Get a new cartridge and start over.

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Dual Epoxy Cartridge
HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Bad Epoxy Mixing Example Climbing Highlining

2. Ah shucks, I drilled the notch too deep and now the eye is recessed too much, how do I fix it???

  • Just put a piece of gravel, small pebble or something non dusty in the bottom of the hole or in the notch, if it will stay, to prop up the bolt until it cures into the position it will be forever.

3. I just heard my bolt hole fart. Does it have enough glue?

  • If air comes out as you put in bolt, it does NOT have sufficient glue!

4. I hammered in my glue in and it won’t go all the way in

  • Wave bolts can feel so tight that it is hard to get them all the way in. I like to lightly wallow out the hole so it isn’t so tight.

  • The other possibility is you didn’t drill the hole deep enough. Take bolt out and redo it. It will be a royal mess!

5. My bolt is on a steep rock and keeps slowly sliding out!

  • Tape it to the rock or worse case wedge a tiny pebble or stick between the rock and the bolt shaft to hold it in place, but be sure your wedge is below the surface of the glue so it doesn’t look sketchy later.

Chapter 10 - How NOT to Bolt

I couldn’t believe how many “How to” videos had mistakes in them. Here is a list of instructional videos we found online and some feedback on their technique.

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Dirty Bolt Hole Always Clean It Climbing Highlining
Glue In Bolt Dirty Hole
  • This video is actually pretty good. They properly install a spin type capsule. If I am going to be overly picky, he doesn’t blow his hole out after brushing it and he left too much glue sticking out, so his plate didn’t sit flush. What is interesting about this video is that it shows that this is how spin capsules are supposed to be installed, whereas climbers don’t do this.

  • This video is another good one, but he doesn’t wear safety goggles. And I’m not just getting on a high horse here as I’ve been hit in the eye before! And it blows dust into his face. I like the fact he uses a proper blow tool. He doesn’t bury the eye which is one of the few instructions Fixe does require! I like that he mentions the hammer leaves iron deposits, so he uses a rubber mallet. I don’t like the fact this is only manually spun to mix the glue, and I’m not excited he keeps pulling it in and out. Is that glue surrounding the shaft entirely or is he getting air pockets doing that?

  • This video here is a really bad example. He only vacuums out the holes which does almost nothing for the dust on the sides of the hole and doesn’t brush them… wow. I also don’t think that he spins it enough.

  • This video is the same as number 3, but uses a cartridge instead of capsule. He vacuums his hole again, which is a shame, and he should put a little glue on the threaded rod before inserting it into hole. You don’t want any air pockets around your threads.

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Danger Sign Learn How to Bolt the Right Way Climbing Highlining
  • This video is pretty good but doesn’t use a wire pipe brush and just hoses out the hole. He also makes a mess which is ok for what he is doing, but not if he did it on rock.

  • This video here is the winner! HOW NOT TO BOLT!!! By Hilti themselves! Installs glue in a dirty hole. He seriously pushes the dust out as he fills the hole with glue!!! The video doesn’t explicitly say it is the SafeSet Technology which is the only exception. That Hilti system can be used without cleaning the hole. This requires a special bolt shaped in a special way and made with a materials that won’t allow the glue to stick to bolt, so when it trys to come out, the HIT-Z bolt flanges on bottom expand the glue like a wedge bolt does to the clip. These bolts are only zinc plated, and no one uses these for climbing applications. The system also requires the HIT-HY 200 glue and not just any epoxy. This video should specify that if it is only for that unique system.

  • This video is by the Access Fund and they did a great video but it has some flaws. He talks about a clean hole, but only cleans it one time. It should be 3x or 4x. He talks about pumping the first squeezes out to make sure the color looks right so the mix is right, but doesn’t do it on camera. He talks about not hitting it directly with a hammer, then does it at the end to twist it into position.

  • A GOOD EXAMPLE… OK, I lied, there was one video by Powers that gets a pat on the back. They clean the shit out of the hole and they pre-squeeze a lot of glue out before putting it in the hole. Look at how much dust comes out on their second phase of blowing it out! And look at the color change as they squeeze out the initial glue. Great example!

HowNOTtoHighline Bolting Bible Book of Installing Glue Ins Bad Bolt Corrosion Climbing Highlining Anchor
Bad Bolt Corrosion
  • Another Good Example… Climbtech put out a good video in a real life climbing situation. They had fancy tools for hanging situations. They were able to reuse the hole from a bolt they removed, and the wave bolt fit in nicely. It wasn’t super tight, but tight enough to hold.

  • Another good example - teamBMC youtube channel had a good video on how to check glue in bolts.

  • Another good example - Derek Bristol has a channel on caving and made a good video about installing glue ins. He also has a good video on Fixe Triplex Removables.

We have 2 glue in bolt installation videos available….

David Keller shows us backwards P (only for specific purposes!)

Here we install bolts for the GGBY Spacenet

Watch all of our bolt videos on this PLAYLIST


If you have feedback, additional information, more correct information, or just good ol' typos that need fixing, please email me at or leave a comment below.


It costs about $10k a year to operate HNTH and no we don't make money on youtube. Please spot us $20 on paypal/venmo or support us per episode on Patreon.


Check The Bolting Bible Home Page

Subscribe to our channel on youtube and hit the bell so you get notified every time we put out a new episode. We talk about bolts, highlining, climbing, gear, break tests and more.

641 views0 comments

Recent Posts

See All